Skip to content

How to Choose TIJ Ink for Your Packaging Material: Read the Container, Not the Resin

B

Brent

· 14 min read

How to Choose TIJ Ink for Your Packaging Material: Read the Container, Not the Resin

Table of Contents

Two lines run the same white PET. One prints a batch code that is still legible after six months in a warehouse. The other loses it somewhere between the case packer and the stretch wrapper. Same resin, same cartridge model, same operator, same shift.

The difference is not the plastic. It is that one of them is a flat label on a carton and the other is a standing pouch with six fold lines, a sealed gusset and a corner that gets crushed every time the pallet is handled.

The short answer: choose TIJ ink for packaging material by container first, then confirm against the resin. The resin decides whether ink can wet the surface at all; the container decides where the code will fail — a fold line, a film of condensation, a heat-sealed tail, an abrasion track, or a stretched sleeve. Five container families cover most packaging lines, each has one dominant failure mode, and each can be tested in under an hour with material already on your floor.

The Resin Tells You Less Than the Container Does

Grouping ink by polymer is not wrong. It is just answering a narrower question than the one buyers usually ask.

Resin-led selection tells you whether the surface energy is high enough for a given ink carrier to spread and grip. That is the chemistry layer, and if it is the layer you are stuck on, it is already documented elsewhere: water-based versus solvent-based TIJ ink works through the porous, semi-porous and non-porous split with cost and dry-time trade-offs, while why ink will not stick to plastic film covers low surface energy and how long corona treatment actually lasts.

This article deliberately does not repeat either; the substrate matching reference collects the energy values, the pretreatment options and the three field tests in one place. It starts one step later, at the point where the ink has already wet the surface correctly and the code still disappears. That failure is geometric and mechanical, and it is decided by what shape you put the material into.

The distinction matters because the same resin behaves like two different materials once formed. A PET film that stays flat holds a code for years. The same film made into a pouch that flexes forty times on its way to the pallet will crack the ink film along the fold. Both are PET. Only one passes.

Five Physical Events That Decide Whether a Code Survives

Almost every real-world code loss traces back to one of five events. They are worth naming because each one calls for a different countermeasure, and only two of them are solved by changing ink.

Bending. The ink film is a pigment dispersed in a resin binder. It is thin, and it is less elastic than the film underneath. Flex it enough times and micro-cracks open along the grain of the character stroke. Once a crack reaches the substrate, the code is gone.

Condensation. A cold surface in warm air collects a film of water within seconds. Ink droplets landing on that film are effectively printing on water, not on packaging. When the water leaves, a chalky residue goes with it.

Heat. Heat seals, shrink tunnels and hot-fill lines raise surface temperature near the code. If the ink has not finished releasing its carrier, the carrier leaves too fast and leaves pinholes. Some surfaces also change their wetting behaviour once heated.

Abrasion. Small formats travel through case packers, conveyors, rails, gates and labelers. Every contact point is a chance to polish off a code that was perfectly adhered in the lab.

Stretch and adhesive. Printing onto a label or a shrink sleeve means printing onto a separate material with its own coating, and then deforming it. A sleeve that shrinks twelve percent takes the ink film with it.

Most packaging triggers at least two of these. A refrigerated stand-up pouch triggers bending, condensation and abrasion before it ever reaches a shelf.

Flexible Pouches: The Fold Is the Real Test

Pouches, sachets and stick packs fail at folds, and nowhere else. The gusset, the top seal shoulder, the bottom corner — these are the places where a formed pouch accumulates flex cycles during filling, cartoning, palletising and transport.

The mechanism is straightforward. Ink on a non-porous film sits entirely on the surface; there is no penetration to anchor it. That makes the bond strong in shear but brittle in flex. Ten folds along the same line will open a crack, and the crack runs perpendicular to the fold, which means it cuts straight through the horizontal strokes of a batch number.

Choosing TIJ ink for flexible pouches is therefore a flex-fatigue question rather than an adhesion question, and it is worth settling before you compare dry times.

Water-based ink is hit hardest here. It bonds well to a properly treated film and it is clean to run, but the dried film is comparatively stiff, which is the wrong property on a package designed to be squeezed.

The test takes one empty pouch:

  1. Print the code in its normal position.
  2. Fold the pouch 180 degrees directly through the middle of the code, press the crease, unfold.
  3. Repeat ten times on the same line.
  4. Rub the crease firmly with a thumb.

Powder on your thumb, or a visible break in a character stroke, means the combination fails. Repeat on a second pouch folded the other way — codes often survive one fold direction and fail the other, because the ink film cracks on the tension side only.

The following is an illustrative composite, not a measured case. A snack producer switched to a new pouch film and started receiving complaints about missing lot codes on the bottom gusset. Adhesion tests passed; the tape pull was clean. The code was printed 8 mm from the gusset fold, and the fold ran through the third character. Moving the print position 15 mm up the panel and switching to a faster-drying solvent formulation together solved it. The ink change alone would not have, and the position change alone would have bought about six months.

Two practical notes. First, check which face of the film is treated — the printable side is the one with the higher surface energy, and printing the untreated side is a reliability problem no ink can fix. Second, if the code has to sit near a fold for regulatory layout reasons, that is a specification to raise with the film supplier, not something to solve at the printhead.

Bottles and Jars: Condensation Sits Between Ink and Wall

Bottles fail for two reasons that look unrelated and are not: the wall is curved, and the wall is wet. Ink adhesion on bottles and tubes is usually judged on flat scrap at room temperature, which is why both problems escape incoming inspection and only appear in the warehouse.

Curvature changes print distance across the width of the code. On a round bottle the head is closer to the centre of the character string and further from the ends, so edge characters spread, lose edge definition or drop out entirely. That behaviour is a function of head-to-surface distance rather than ink, and it is covered in detail in printing on curved and uneven surfaces.

Condensation is the more expensive problem because it is intermittent. A bottle filled cold, or moved from a 4 degree cold room into a 25 degree packing hall, collects visible moisture in under two minutes. Printing during that window produces a code that looks acceptable wet and wipes off with a thumb once dry. The ink never contacted the polymer; it contacted water.

This is why the same line can run perfectly all morning and fail every afternoon in summer, and why the failure so often gets blamed on a bad batch of cartridges. The cartridge did not change. The dew point did.

The field test is deliberately crude: take a bottle straight from the cold store, stand it in the packing hall, watch until the surface just starts to fog, then print immediately. Wipe with a damp cloth after thirty seconds. If the code smears or lifts, your window is narrower than your process.

Countermeasures, cheapest first: print after the bottle has equalised, add an air knife or a dry-air curtain at the print station, or move the code onto the label where the label’s own coating gives the ink something dry to bite. If your product also travels frozen, the cold-chain failure modes stack on top of these and are worth reading separately.

Tubes: The Tail Seal Is a Heat Zone

A tube is printed on a curved, coated surface and then sealed at the tail with a heated jaw. The seal is the problem.

Heat does not stay inside the jaw footprint. It spreads through the laminate, and the spread is wider than most people assume — enough to reach a code printed a few millimetres above the seal line. If the ink is still releasing carrier when that heat arrives, the carrier leaves faster than the film can consolidate, which produces a porous, low-holding film. It can look fine on the line and fail a rub test a week later.

There is a second, subtler effect. Some tube laminates carry a slip additive or a lacquer that changes behaviour once warmed, and the printable face that accepted ink at 22 degrees is not the same face at 60.

The test costs three tubes. Print at 5 mm, 10 mm and 15 mm above the tail seal, run all three through the sealing machine, then compare. Whichever distance still passes is your minimum offset. In most tube lines this lands between 10 and 15 mm, and the answer is worth writing into the artwork, because it is the cheapest fix available: no ink change, no new cartridge, just a print position that respects the heat.

If the layout will not allow the offset, then a faster-drying solvent ink buys margin, and a chill block or air knife between the printer and the sealer buys more.

Blisters and Small Cartons: The Code Has to Survive the Machine

Small formats are the most abrasive environment in packaging, and the abrasion happens after printing, off-camera, inside equipment nobody thinks of as part of the coding process.

A blister card, a small folding carton, a sachet or a vial label passes through a cartoner, a shrink bundler, a checkweigher, several conveyor transfers and often a labeller. Each of those has rails, guide plates, star wheels and pushers that contact the printed face. A code with excellent adhesion but poor abrasion resistance will still be legible at the end of the printer and unreadable at the end of the line.

Aluminium blister lidding is a special case: the foil is thin, the lacquer layer that accepts ink is thin, and the web is under tension as it indexes. Codes there need both a formulation matched to the lacquer and a verification step downstream, not just at the print head.

The test is to run twenty printed blanks through the real downstream equipment with no product, then compare against a control set that stayed in the box. Photo both sets under the same light. If the machine-run set shows thinning on the leading edge of characters, you have an abrasion problem, and the answer is a harder-drying film rather than a bigger drop size.

Labels and Shrink Sleeves: You Are Printing on a Wrap, Not a Wall

When the code goes onto a label or a shrink sleeve, the substrate is no longer the packaging material. It is a coated film with its own surface treatment, sometimes a release agent on the reverse, and in the case of sleeves, a defined shrink ratio.

Three things follow. A release agent that migrated to the print face will defeat almost any ink. A sleeve that shrinks ten to fifteen percent will stretch the ink film by the same amount in the machine direction, and a film that cannot stretch that far will craze. And the shrink tunnel is a heat event on top of both.

Printing on a sleeve is viable, but TIJ ink for shrink sleeves has to be chosen for the sleeve rather than for the bottle. Ask the sleeve supplier three questions before committing: what the print face is, whether any slip or release additive is present, and what the shrink ratio and tunnel temperature are. A code designed around a 40 percent shrink sleeve is a different ink decision from the same code on a 12 percent sleeve.

Where regulation allows it, printing directly on the container removes this entire layer of risk. Where it does not, print on the sleeve but test through the tunnel, not before it.

A Container-First Selection Table

This is the working version of the whole article. Read down the container column, and treat the ink direction as the starting point for a trial rather than a specification.

ContainerDominant failureInk directionField testCheapest fix
Stand-up pouch, sachetFold-line crackingFast-dry solvent, flexible filmTen folds through the code, then thumb rubMove the code off the fold
Bottle, jarCondensation filmFast-dry solvent, dry air at stationPrint on first fog, wipe after 30 sEqualise temperature or add air knife
TubeTail-seal heatFast-dry solvent with heat tolerancePrint at 5, 10, 15 mm, then sealRaise the code 10 to 15 mm
Blister card, small cartonMachine abrasionHard, abrasion-resistant solventRun 20 blanks through the line dryReduce contact on the print face
Label, shrink sleeveStretch and coatingFormulated for the label stockPrint, then pass the shrink tunnelPrint on the container instead
Flat carton, corrugatedWicking and set-offWater-based is usually enoughStack 24 h, then check for transferImprove stacking or dry time

Two entries deserve a warning. Corrugated and uncoated board are the easy case, and buyers over-specify solvent ink on them out of habit, paying for dry speed and odour they do not need. Metal and glass are the opposite: they grip a correctly chosen solvent ink very well, which is why adhesion on metal is usually a cleanliness and cure-time question rather than a formulation one.

Five Tests to Run Before You Switch Ink

None of these need a laboratory, and all five can run on scrap material in a single afternoon. Run them in this order, because each one eliminates a different variable.

Fold and rub. Ten folds through the code, then a firm thumb rub. Tests flex fatigue. This is the first test for any flexible package.

Condensation wipe. Chill the container, print at the first sign of fog, wait thirty seconds, wipe with a damp cloth. Tests whether your ink is reaching the substrate or only the water on top of it.

Tape pull. Apply standard adhesive tape over a fully dried code, press firmly, pull at a shallow angle. A clean pull means adhesion is adequate. Repeat after the code has cured for the full interval your process allows, not immediately.

Dry run through the line. Twenty printed blanks through the actual downstream equipment. Tests abrasion in the only place it happens.

Heat pass. A heat gun at the temperature your seal or tunnel reaches, held for the dwell time your process uses. Tests whether the ink survives the thermal event, not just the ambient one.

Record pass or fail for each, on the same sheet, for the old ink and the new one. A trial that only reports “better adhesion” is not a trial, because adhesion was never the variable that failed.

What to Send a Supplier Before You Ask for a Quote

Most ink trials fail at the enquiry stage, because the enquiry describes the packaging material and stops there. A supplier who only knows the resin can only guess at the container, and the guess is where the mismatch enters.

Send six things and the conversation changes:

  1. The substrate, named properly. Not “plastic film” — the film type, thickness, and whether the print face is corona or chemically treated.
  2. The container form and a dimension. Pouch with gusset, 250 ml bottle with 38 mm neck, 75 mm tube.
  3. A print position drawing. Distance from the nearest fold, seal, tail jaw or sleeve edge. This single drawing prevents most of the failures described above.
  4. The downstream equipment list. Cartoner, bundler, shrink tunnel, labeller — with temperatures where they matter.
  5. Storage and transport conditions. Cold chain, hot fill, freezing, humidity.
  6. A photo of a current failure. The pattern of the loss — cracks on a fold, a chalky smear, thinning on a leading edge — narrows the cause faster than any description.

If you are qualifying a new source and want the container-level tests run against your own packaging, FirstColor can compare formulations on your pouches, bottles or tubes and report each of the five tests separately; the contact form takes the substrate details and a sample request together. As with any supplier, validate on your line before scaling the order.

Conclusion

Ink selection guides are usually organised around chemistry, and chemistry is real — but it is the entry condition, not the verdict. The question that decides whether your code survives the pallet, the cold room and the cartoner is a question about shape.

A pouch fails at its fold. A bottle fails in its condensation. A tube fails at its tail seal. A small carton fails somewhere in the machinery after the printer. A sleeve fails when it shrinks. None of those failures are visible in a surface energy table, and all of them are testable with scrap material and an afternoon.

Start from the container, confirm against the resin, and let the five tests settle it.

FAQ

Can one ink cover all the packaging on my line? Rarely, and the exceptions are usually cheap to isolate. Corrugated and uncoated board accept water-based ink without trouble, while a cold-filled bottle on the same site needs a fast-dry solvent. The practical answer is to group your packaging by container family first and see how many families you actually have — most plants discover they need two inks rather than five.

The tape test passes but the code rubs off in transit. What does that mean? It means you have adhesion but not abrasion resistance, and the two are different properties. Tape pull measures how hard it is to lift the film from the surface; abrasion measures how well it survives repeated light contact. A code can pass one and fail the other, which is why the dry run through the downstream equipment belongs in the test set.

Does a dark or transparent container need a different ink? A dark container needs sufficient contrast, which may mean a light-coloured or white ink rather than a formulation change, and that brings its own handling requirements around pigment settling. A transparent container raises the opposite question: whether the code is being read through the wall or from the print face, because the two put different optical demands on the code.

Why does the code only fail on refrigerated bottles? Because the print window is being missed, not because the ink is wrong. A cold bottle collects a water film within a couple of minutes in a warm hall, and ink printed onto that film never reaches the polymer. Print after temperature equalisation, or dry the surface at the station, and the same cartridge usually performs.

How long does a proper trial take? The five tests take an afternoon on scrap material. What takes longer is the waiting: a code should be evaluated after it has cured for the full interval your process allows, and a transport simulation needs at least one real pallet. A same-day verdict on adhesion is normal; a same-day verdict on survival is not.